2026 Polygon COLLOSUS N9 Di2 CARBON

Archived: Frame: ACX & ALX ENDURO 170mm TRAVEL · Fork: ROCKSHOX ZEB ULTIMATE, 170mm TRAVEL

• Inspect the frame in bright light, especially the head tube, bottom-bracket area, chainstays and clamped surfaces. Look for cracks, ripples, crushed sections or signs of impact.

Archived: Fork: ROCKSHOX ZEB ULTIMATE, 170mm TRAVEL · Rear shock: ROCKSHOX VIVID SELECT+, E2E: 230x65mm

• Inspect the fork stanchions for scratches or coating wear, look for oil or dirt rings at the seals, and cycle the fork through its travel while checking for binding or bushing play.
• Inspect the shock shaft and seals, cycle the rear suspension through its travel and check for oil, air loss, binding or unusual top-out and bottom-out noises.
• Hold the rear brake and load the suspension from several directions. Check pivots, bearings and mounting hardware for knock, looseness or side play.
• Ask for dated fork, shock and pivot-service records. A clean exterior does not establish the condition of internal seals, oil, bushings or bearings.

Archived: Shifters: SHIMANO XTR DI2 SW-M9250 I-SPEC EV, 1x12-SPEED · Rear derailleur: SHIMANO XTR DI2 RD-M9250 · Crankset: SHIMANO XTR FC-M9220, 32T · Bottom bracket: SHIMANO SM-BB93 · Cassette: SHIMANO XTR CS-M9200 10-51T · Chain: SHIMANO XTR CN-M9100

• Confirm every shift battery charges and every control operates. Shift through the full cassette under light load while checking pairing, derailleur alignment and response at both ends of the range.
• Measure chain wear with a compatible gauge and inspect chainring, cassette or freewheel teeth. A new chain does not rule out wear in the remaining drivetrain.
• Turn the cranks slowly, feel for rough bearings and check for side-to-side play. Inspect crank arms, chainring bolts and pedal threads for looseness or damage.

Archived: Brakes: SHIMANO XTR BL-M9220; Levers: SHIMANO XTR BL-M9220; Rotors: SHIMANO CL-900, 203mm

• Inspect pads and braking surfaces, check the complete cable or hose path, and confirm both controls feel consistent and return cleanly.

Archived: Wheels: POLYGON MT6 TUBELESS READY · Rims: ALLOY DOUBLE WALL H:18mm W: 30mm 622-30 32H FOR TYRE 622-54/76 TL READY · Hubs: F: SHIMANO XT HB-M8110-B BOOST 15x110mm 32H CL / R: SHIMANO DEORE XT FH-M8110-B BOOST 12x148mm 32H CL FOR MICRO SPLINE · Front tire: MAXXIS ASSEGAI 29"x2.5" (622-63) · Rear tire: MAXXIS ASSEGAI 29"x2.5" (622-63)

• Spin both wheels and watch for side-to-side and vertical movement. Check spoke tension, rim condition and hub play.
• Inspect both tire casings for cuts, cracking, plugs, bulges or exposed threads and confirm the installed sizes are safe for the rims and available frame and fork clearance.
• Confirm whether the bike is actually set up tubeless, whether both tires hold pressure, and when sealant and rim tape were last serviced.

Archived: Headset: FSA NO.57E W/ SEALED BEARING ZS 44/28.6 | ZS 56/40 · Handlebar: RACE FACE CHESTER 35, W: 780mm, BB: 35mm, R/D: 35mm, B: 8degree · Stem: RACE FACE AEFFECT R 35, EXT: 40mm, BB: 35mm, R/D: 0degree · Seatpost: TRANZ X JD-YSP39KL 150mm (S, M) / 170mm (L, XL) TRAVEL, DxL: 34.9 x 456mm (S, M) / 495mm (L, XL) · Saddle: LINC XTENT · Pedals: ALLOY FLAT W/ REPLACEABLE PIN

• Apply the front brake and rock the bike to check for headset play or notchiness. Inspect the stem, handlebar and clamp zones, then confirm every fastener and control is secure.
• Check that the seatpost moves for adjustment and that the saddle, post and clamp hold securely without cracks, severe corrosion or damaged hardware.