Specifications & Value

Reading Velopedia’s Specification Analysis

By Updated November 3, 2026

Velopedia’s specification analysis is a reading aid for the Bicycle Archive. It takes details such as cassette tooth counts, wheel labels, frame material, brake type, and suspension equipment, then explains a relationship or inspection consequence that isn’t obvious from a parts list alone. It is not a review score, fit recommendation, appraisal, or report on the condition of a particular bicycle.

Start with Original build, then read the relevant Geometry, Gearing, Replacement parts, Inspection, or Market section. The tables and calculations describe the archived model and build. Check the record’s source and notes for provenance. They do not establish what is currently installed on a used bike.

Read the page in three layers

An Archive page contains three different kinds of information. Keeping them separate prevents most misreadings.

1. The archived specification

The specification tables preserve model-year information such as the frame, fork, drivetrain, brakes, wheels, tires, sizes, colors, geometry, weight, and original MSRP when those details are available. This is the evidence layer.

Specifications can vary by country, frame size, production run, or later substitution. A used bicycle may also have years of replacement parts. The record identifies the documented build; it does not certify that a bicycle remains original.

Use the frame-size and wheel-setup selectors in Geometry where offered. In Gearing, read each result’s own size and build labels; a geometry selection does not necessarily filter every other section. If the source lists different tires or equipment by size, match the relevant row to the bicycle you are researching.

2. A calculation or normalization

Velopedia may calculate complete gear ratios and total range from resolved chainring, sprocket, and transmission inputs; estimate speed when rear-wheel information is supported; or translate a familiar wheel name into its ISO bead-seat diameter. It also groups varied source wording into broad material or brake families. These operations make unlike catalog descriptions easier to compare, but their accuracy depends on the inputs.

The calculation should be reproducible from the fields shown on the page. Normalization is broader: it organizes source wording without pretending that every product in the category is interchangeable.

3. The practical meaning

The explanations and inspection checklist turn archived details into questions for a buyer, owner, or mechanic. A carbon-frame label changes the inspection emphasis. A press-fit bottom bracket raises more compatibility questions than the words “press fit” answer. A tubeless-ready label describes capability, not how the tires are set up today. A suggested replacement still needs its exact interfaces checked against the installed parts.

What the common sections are telling you

Section or evidenceWhat it establishesWhat it does not establish
GearingLowest and highest complete ratios, and total range, when drivetrain inputs are resolvedDrivetrain condition, rider effort, or every intermediate shift step from endpoint tooth counts alone
Cadence and speedEstimated speed from gear ratio, cadence, and supported rear-wheel circumferencePower required, achievable climbing speed, traction, or an exact measured rollout
Wheel standardNominal wheel label and, where supported, ISO bead-seat diameterTire width, rim width, clearance, axle standard, or tire compatibility by itself
Frame inspectionMaterial family and the damage patterns that deserve attentionPresent condition, crash history, or internal structural integrity
Suspension setupWhether front and/or rear suspension is documented in the archived recordService condition, correct setup, remaining travel, or proof that every original component is still fitted
Brake serviceBroad brake-system type and the relevant area of servicePad or rotor life, fluid condition, cable condition, or a universal wear limit
Bottom bracketA documented interface or the need to verify more dimensionsThe exact replacement assembly unless the shell and crank standards are fully identified
Tire setupPublished tubeless capability or a documented tire arrangementWhether tubes are installed, whether sealant is fresh, or whether the current tire and rim combination is approved
Published weightThe archived figure supplied for the modelThe weight of every size or the bicycle now being inspected
Original MSRPHistorical suggested-price contextCurrent retail price, depreciation, asking price, or used value

The sections and results depend on the evidence available for that record. They are not a fixed set of findings that appears identically on every bicycle. A calculated value remains conditional on the documented build and any stated approximation.

How cassette range is calculated

When the smallest and largest cassette sprockets are clear, Velopedia calculates:

largest sprocket ÷ smallest sprocket × 100

An 11–46-tooth cassette has approximately 418% cassette range because 46 ÷ 11 × 100 ≈ 418. With one chainring and no additional variable-ratio transmission, the complete gear range is the same percentage. With multiple chainrings or internal gearing, calculate the complete highest and lowest ratios before describing the bicycle’s total range.

For a conventional chain drive, gear ratio = front chainring teeth ÷ rear sprocket teeth. A smaller ratio is a lower gear. Total range = highest complete ratio ÷ lowest complete ratio × 100. Include any internal hub or gearbox ratio when present. Changing a single chainring changes the low and high ratios together, while leaving the cassette’s percentage range unchanged.

For example, a 30-tooth chainring with an 11–50 cassette gives a lowest ratio of 30 ÷ 50 = 0.60 and a highest ratio of 30 ÷ 11 ≈ 2.73. Use the unrounded ratios for the range: (30 ÷ 11) ÷ (30 ÷ 50) × 100 ≈ 454.5%, normally rounded to 455%. These are illustrative inputs, not specifications assigned to a particular archived bike.

A 30T chainring and the 11T and 50T cassette endpoint sprockets show the known tooth counts. The lowest ratio is 0.60, highest 2.73 and range about 455 percent. Speed additionally needs wheel rolling circumference and cadence.
Tooth counts establish ratios without a known tire size. A speed estimate requires rear-wheel rolling circumference and cadence as separate inputs.

Wheel circumference converts a ratio into distance traveled. Estimated speed (km/h) = cadence (rpm) × overall gear ratio × rear-wheel rolling circumference (m) × 60 ÷ 1,000. Tire dimensions provide an estimate; a measured rollout at the intended pressure and load gives a better circumference input. This is a motion calculation, not a prediction of the power you can produce or the speed you can sustain.

An uncertain rear tire can therefore prevent a speed estimate while leaving valid gear ratios and range available. On a mixed-wheel bike, the driven rear wheel controls this calculation. Tire size and crank length do not change the tooth-count ratio; tire circumference changes distance per revolution, and crank length changes the rider’s leverage. Endpoint counts alone do not reveal all the steps between gears.

Why 700C and 622 mm appear together

Traditional wheel names are not dependable compatibility measurements by themselves. The 700C label normally corresponds to a 622 mm bead-seat diameter, where the tire bead sits in the rim. A 29-inch mountain-bike tire also uses a 622 mm bead-seat diameter. That number is not the complete wheel’s outside diameter: tire size changes the outer radius and rolling circumference.

The mapping narrows the compatibility question; it does not finish it. Tire width, inner rim width, frame and fork clearance, brake position, and manufacturer limits still matter. Inch labels are especially ambiguous because different bead-seat diameters have shared names such as “26 inch” or “28 inch.” Read the tire sidewall and rim marking rather than ordering from the inch name alone.

A documented 29-inch front and 27.5-inch rear arrangement uses different bead-seat diameters: 622 mm and 584 mm. Tires and rims must match the appropriate end; complete replacement wheels also need the correct axle, brake, and drivetrain interfaces. Tubes are different: some are approved for several diameters and widths, so follow the tube maker’s printed size range and valve requirements. An unqualified “27.5/29” source entry may list alternative sizes; it does not by itself prove a mixed-wheel arrangement.

Treat inspection prompts as priorities, not diagnoses

A material-based inspection prompt directs attention to relevant failure signs. Aluminum and steel frames deserve careful inspection around welds, loaded junctions, dents, deformation, and corrosion where applicable. Carbon or other composite frames shift the emphasis toward impact areas, crushed clamping zones, broken fibers, delamination clues, and unexplained changes in shape. The checklist cannot clear a frame for use.

The same distinction applies to brakes and suspension. “Hydraulic disc” tells you to inspect pad and rotor condition, hose integrity, lever feel, leakage, and use of the correct service fluid. Exact wear limits come from the component manufacturer, not the category label. “Front suspension” identifies a fork as an inspection and service item; it says nothing about bushing play, damper function, air pressure, spring rate, or service history.

Use the linked used-bike inspection guide when a prompt identifies an area that needs physical checking. Marking an item complete records your progress; it is not a pass certificate or proof of safety. The checklist progress stays in that browser for that record unless you use the separate save workflow.

Missing analysis is not a negative finding

Archive records are uneven because historical source material is uneven. If a wheel size, tooth-count span, brake family, or suspension arrangement cannot be resolved from the available evidence, the interpretation may be omitted or qualified. Missing analysis does not prove that the component or feature is absent.

Read the underlying table and note any ambiguity. A bare model name may not expose a service standard. A generic “disc brake” entry may not distinguish mechanical from hydraulic operation. A tire label may combine marketing language with dimensions that need verification. Do not fill those gaps by assumption when ordering parts.

Conflicting size-specific geometry and a shared tire description need special care. Read the selected size’s evidence, preserve the uncertainty, and verify the actual rear tire before relying on wheel-dependent results. A generic alternative-size list should not be silently turned into one certain configuration.

Use the analysis to form the next question

The analysis works best as a handoff from research to verification:

  1. Confirm that you have the correct model, year, size, and build.
  2. Read the analysis for the relationships most likely to affect inspection or compatibility.
  3. Check the source fields in the specification and geometry tables.
  4. Compare the archived build with the physical bicycle.
  5. Use the exact component model and manufacturer documentation before service or parts ordering.

The Velopedia comparison tool is useful when two records have similar names or when you are deciding between model years. Compare the source specifications first, then use the analysis to understand which differences change fit, service, inspection, or parts compatibility.

For price questions, move to the guide to original MSRP and used-market data. Specification analysis can describe a bike’s equipment and original market position, but it cannot value the condition of the bicycle in front of you.

Sources and technical review

Author: Jeff South
Technical review date: August 15, 2026

Scroll to Top