2024 Rocky Mountain Slayer Alloy 30

Archived: Frame: FORM™ Alloy | Full Sealed Cartridge Bearings | Press Fit BB | Internal Cable Routing | 2-Bolt ISCG05 Tabs | RIDE-4™ Adjustable Geometry | 2 Position Axle | 180mm Travel. FORM™ Alloy Rear Triangle · Fork: RockShox Domain RC | 180mm | 44mm Offset

• Look for dents or shape changes and inspect the edges of welds around the head tube, bottom bracket, seat cluster and suspension mounts for hairline cracks.

Archived: Fork: RockShox Domain RC | 180mm | 44mm Offset · Rear shock: Marzocchi Bomber CR | Steel Spring | Sealed Bearing Eyelet | 25x8mm F Hardware | All Sizes = 230 x 65mm | Coil Spring SM - MD - LG - XL = 400 - 450 - 500 - 550

• Inspect the fork stanchions for scratches or coating wear, look for oil or dirt rings at the seals, and cycle the fork through its travel while checking for binding or bushing play.
• Inspect the shock shaft and seals, cycle the rear suspension through its travel and check for oil, air loss, binding or unusual top-out and bottom-out noises.
• Hold the rear brake and load the suspension from several directions. Check pivots, bearings and mounting hardware for knock, looseness or side play.
• Ask for dated fork, shock and pivot-service records. A clean exterior does not establish the condition of internal seals, oil, bushings or bearings.

Archived: Shifters: Shimano Deore 12spd · Rear derailleur: Shimano Deore 12spd · Crankset: Shimano Deore | 32T | 24mm Spindle | SM = 165mm | MD - XL = 170mm · Bottom bracket: Shimano SM-BBMT500 · Cassette: Shimano Deore 10-51T 12spd · Chain: Shimano M6100

• Shift through every available gear under light load. Hesitation, skipping or inconsistent indexing can reflect wear, damage, poor adjustment or mismatched replacement parts.
• Measure chain wear with a compatible gauge and inspect chainring, cassette or freewheel teeth. A new chain does not rule out wear in the remaining drivetrain.
• Turn the cranks slowly, feel for rough bearings and check for side-to-side play. Inspect crank arms, chainring bolts and pedal threads for looseness or damage.

Archived: Brakes: Shimano MT4120 4 Piston | Metal Pads

• Inspect pads and braking surfaces, check the complete cable or hose path, and confirm both controls feel consistent and return cleanly.

Archived: Wheel size: 29/27.5; 29" · Rims: WTB ST i30 TCS 2.0 Tubeless | 32H / Tubeless Ready - Tape / Valves Incl · Hubs: Front: Shimano TC500 | 15x110m; Rear: Shimano TC500 Boost 148mm · Front tire: Maxxis Assegai 2.5 WT 3C MaxxGrip DD Tubeless Ready · Rear tire: Maxxis Minion DHR II 2.4 WT 3C MaxxTerra DD Tubeless Ready //

• Spin both wheels and watch for side-to-side and vertical movement. Check spoke tension, rim condition and hub play.
• Inspect both tire casings for cuts, cracking, plugs, bulges or exposed threads and confirm the installed sizes are safe for the rims and available frame and fork clearance. This record indicates different front and rear wheel diameters, so verify each tire at its correct end.
• Confirm whether the bike is actually set up tubeless, whether both tires hold pressure, and when sealant and rim tape were last serviced.

Archived: Headset: FSA Orbit NO.57E ZS44|56 | Sealed 36°x45° Bearings | 30.2mm x 41mm x 7.1mm Upper | 40mm x 51.8mm x 7.5mm Lower | 1.5" Crown Race · Handlebar: Rocky Mountain AM | 780mm Width | 38mm Rise | 9° Backsweep | 5° Upsweep | 35 Clamp · Stem: Rocky Mountain 35 AM | 5° Rise | All Sizes = 40mm · Seatpost: X Fusion Manic Composite 30.9mm | SM = 150mm | MD = 170mm | LG - XL = 200mm · Saddle: WTB Volt Race 142

• Apply the front brake and rock the bike to check for headset play or notchiness. Inspect the stem, handlebar and clamp zones, then confirm every fastener and control is secure.
• Check that the seatpost moves for adjustment and that the saddle, post and clamp hold securely without cracks, severe corrosion or damaged hardware.