2026 Commencal T.E.M.P.O. T-Type

Archived: Frame: T.E.M.P.O., 125 mm travel29'', Alloy 6069, triple butted tubes, T4, T6. · Fork: FOX 36 Factory, 150 mm travel29", Float, Grip 2 damper, HSR, LSR, HSC, LSC, Boost (15 x 110 mm), 51 mm offset, 2 spacers

• Look for dents or shape changes and inspect the edges of welds around the head tube, bottom bracket, seat cluster and suspension mounts for hairline cracks.

Archived: Fork: FOX 36 Factory, 150 mm travel29", Float, Grip 2 damper, HSR, LSR, HSC, LSC, Boost (15 x 110 mm), 51 mm offset, 2 spacers · Rear shock: FOX Float X Factory210 x 50, LSC,LSR, 2-postion adjustment, 0.2 spacer

• Inspect the fork stanchions for scratches or coating wear, look for oil or dirt rings at the seals, and cycle the fork through its travel while checking for binding or bushing play.
• Inspect the shock shaft and seals, cycle the rear suspension through its travel and check for oil, air loss, binding or unusual top-out and bottom-out noises.
• Hold the rear brake and load the suspension from several directions. Check pivots, bearings and mounting hardware for knock, looseness or side play.
• Ask for dated fork, shock and pivot-service records. A clean exterior does not establish the condition of internal seals, oil, bushings or bearings.

Archived: Shifters: SRAM AXS Pod Controller12s · Rear derailleur: SRAM X0 Eagle Transmission12s, AXS · Crankset: SRAM X0 Eagle Transmission, 170 mm crank arms, DUBChainring: SRAM X0 Eagle Transmission, 32t, Narrow-Wide · Bottom bracket: SRAM DUBPressfit · Cassette: SRAM X0 Eagle TransmissionCS 1295, 12s, 10-52t · Chain: SRAM X0 Eagle Transmission12s, Flattop chain

• Confirm every shift battery charges and every control operates. Shift through the full cassette under light load while checking pairing, derailleur alignment and response at both ends of the range.
• Measure chain wear with a compatible gauge and inspect chainring, cassette or freewheel teeth. A new chain does not rule out wear in the remaining drivetrain.
• Turn the cranks slowly, feel for rough bearings and check for side-to-side play. Inspect crank arms, chainring bolts and pedal threads for looseness or damage.

Archived: Brakes: SHIMANO XT, 2 pistons, I-Spec EV, resin padsRotor: SHIMANO RT-MT905 203 / 180 mm, 6-bolt

• Inspect pads and braking surfaces, check the complete cable or hose path, and confirm both controls feel consistent and return cleanly.

Archived: Rims: DT SWISS XMC 1501; 29'', 28h, 30 mm inner width · Hubs: Rear: DT SWISS 240 - Front: DT SWISS 240Rear: 28h, sealed bearings, 12 x 148 mm, Ratchet EXP 36, Sram XD freehub body - Front: 28h, sealed bearings, 15 x 110 mm · Front tire: MAXXIS DHR II; 29" x 2.4" WT, 3C MaxxGrip, EXO, Tubeless Ready · Rear tire: MAXXIS Dissector; 29" x 2.4" WT, 3C MaxxTerra, EXO, Tubeless Ready

• Spin both wheels and watch for side-to-side and vertical movement. Check spoke tension, rim condition and hub play.
• Inspect both tire casings for cuts, cracking, plugs, bulges or exposed threads and confirm the installed sizes are safe for the rims and available frame and fork clearance.
• Confirm whether the bike is actually set up tubeless, whether both tires hold pressure, and when sealant and rim tape were last serviced.

Archived: Headset: ACROS ZS56 / ZS56Alloy cups, sealed bearings, Integrated cable routing · Handlebar: RENTHAL Fatbar Lite on S/M - RENTHAL Fatbar on L/XL31.8 mm, 760 mm width, 30 mm rise, Alloy 6061 on S/M - 31.8 mm, 800 mm width, 30 mm rise, Alloy 6061 on L/XL · Stem: RENTHAL Apex40 mm extension, 31,8 mm · Seatpost: FOX Transfer Factory31.6 mm, 150 mm on S, 175 mm on M/L, 200 mm on XL · Saddle: FIZIK Terra Ridon X5145 mm width, S-alloy rails · Pedals: No

• Apply the front brake and rock the bike to check for headset play or notchiness. Inspect the stem, handlebar and clamp zones, then confirm every fastener and control is secure.
• Cycle the dropper post repeatedly. It should reach full travel, remain extended under load and have no unusual oil, excessive rotational play or damaged remote, cable, hose or battery.