2015 Specialized Status II

Archived: 2015 Specialized Status II · Mountain Dual Suspension · Published sizes: Grom, XS, S, M, L

• Confirm the frame markings and seller description match this archived model. Note every component that differs from the published build.
• Record the frame serial number. It should be legible, unaltered and consistent with the seller’s ownership history.
• Find the size marking on the bicycle and confirm the fit before judging the condition or price.

Archived: Frame: M4 hydroformed tubing, 1.5" forged headtube, ISCG mounts, 135mm rear spacing, full-cartridge bearing pivots, 200mm travel · Fork: RockShox Boxxer RC, alloy steerer, compression and rebound adj., 20mm Maxle DH thru-axle, XS/S: extra-soft spring, M: soft spring, L: medium spring, 200mm travel · Suspension

• Look for dents or shape changes and inspect the edges of welds around the head tube, bottom bracket, seat cluster and suspension mounts for hairline cracks.
• Stand behind and in front of the bicycle to look for obvious frame, fork or wheel misalignment. Ask directly about crashes, transport damage and repairs.

Archived: Fork: RockShox Boxxer RC, alloy steerer, compression and rebound adj., 20mm Maxle DH thru-axle, XS/S: extra-soft spring, M: soft spring, L: medium spring, 200mm travel · Rear shock: Custom FOX VAN RC, coil w/ piggy back, compression and rebound adj., 8.75x2.75", XS: 350, S: 400, M: 450, L: 500

• Inspect the fork stanchions for scratches or coating wear, look for oil or dirt rings at the seals, and cycle the fork through its travel while checking for binding or bushing play.
• Inspect the shock shaft and seals, cycle the rear suspension through its travel and check for oil, air loss, binding or unusual top-out and bottom-out noises.
• Hold the rear brake and load the suspension from several directions. Check pivots, bearings and mounting hardware for knock, looseness or side play.
• Ask for dated fork, shock and pivot-service records. A clean exterior does not establish the condition of internal seals, oil, bushings or bearings.

Archived: Group: DH mix · Shifters: SRAM X5, 9-speed, trigger · Rear derailleur: SRAM X7, 9-speed, short cage · Crankset: Custom SRAM Descendant, GXP spindle, 7050 alloy arms, 165mm, 36T · Bottom bracket: SRAM GXP XR, 73mm · Rear cogs: SRAM PG 950, 9-speed, 11-28 · Chain: SRAM PG 971, 9-speed, w/ PowerLink

• Shift through every available gear under light load. Hesitation, skipping or inconsistent indexing can reflect wear, damage, poor adjustment or mismatched replacement parts.
• Measure chain wear with a compatible gauge and inspect chainring, cassette or freewheel teeth. A new chain does not rule out wear in the remaining drivetrain.
• Turn the cranks slowly, feel for rough bearings and check for side-to-side play. Inspect crank arms, chainring bolts and pedal threads for looseness or damage.

Archived: Brakes: SRAM Guide R, metallic pads, Guide R caliper, 200mm Centerline rotor, SRAM Guide R, metallic pads, Guide R caliper, 180mm Centerline rotor

• Inspect pads, cables and housings, then examine both rim braking surfaces for concavity, cracking or heavy wear. Confirm each caliper returns and centers correctly.
• Before riding, test every installed brake separately at walking speed. Each should stop firmly and release cleanly without its control reaching the end of its usable travel.

Archived: Wheel size: 26 · Rims: P.Disc, 24mm inner width, 36h · Hubs: Specialized Hi Lo disc, sealed cartridge bearings, 20mm thru-axle, 36h, Specialized Hi Lo disc, bolt-on, sealed cartridge bearings, 10mm thru-axle, 36h · Front tire: Specialized Butcher DH, 60TPI, wire bead, soft dual compound, 26x2.5", Specialized Butcher DH, 60TPI, wire bead, soft dual compound, 26x2.3"

• Spin both wheels and watch for side-to-side and vertical movement. Check spoke tension, rim condition and hub play.
• Inspect both tire casings for cuts, cracking, plugs, bulges or exposed threads and confirm the installed sizes are safe for the rims and available frame and fork clearance.
• Remove and reinstall or closely inspect both wheel-retention systems. Axles or quick releases should tighten correctly with undamaged threads, hardware and dropouts.

Archived: Headset: Semi-integrated alloy cups for 1-1/2" headtube and 1-1/8" steerer, cartridge bearings · Handlebar: Specialized Demo, low rise, 6061 alloy, 9-degree backsweep, 6-degree upsweep, 31.8mm · Stem: Specialized P.Series MTB, forged alloy, 4-bolt · Seatpost: Specialized 6061 alloy, 2-bolt, 0mm setback, 30.9mm · Saddle: Specialized DH, 8mm steel rails · Pedals: Specialized Bennies, 6061 alloy body, sealed cartridge, 4.5mm removable pins

• Apply the front brake and rock the bike to check for headset play or notchiness. Inspect the stem, handlebar and clamp zones, then confirm every fastener and control is secure.
• Check that the seatpost moves for adjustment and that the saddle, post and clamp hold securely without cracks, severe corrosion or damaged hardware.

• Before riding, confirm both wheels are secure, tires are safe, both brakes function, and the headset, handlebar, stem, cranks and pedals have no looseness.
• Begin at low speed. Test steering, braking and shifting progressively, then load the drivetrain and suspension only after the basic safety checks pass.
• Listen and feel for repeated knocks, grinding, skipping, brake pulsation or movement at joints. Stop the test if the bicycle cannot be controlled safely.